THE ULTIMATE IN STEERING COMFORT…
INTRODUCTION
• Experience the ‘automotive style’ comfort hydraulic steering can achieve with the new and innovative SeaStar Power Assist.
• Designed for difficult and hard to steer boats.
• Perfect addition for all O/B, I/O, I/B powered boats, equipped with standard hydraulic steering.
Part # PA1200-2, PA1225-2 and PA1315-2 (PRO Series)
Applications
• 150HP+ single outboards.
• Heavy 4 stroke outboards.
• Twin/Triple outboards.
• Inboards where rudder torque makes wheel effort heavy or uncomfortable.
Features
• Dramatically increases steering comfort.
• Reduced wheel effort.
• Easy installation.
• Simple ‘add-on’ to existing SeaStar manual system (up to 2.0cu. in. helms).
• Number of turns lock to lock remains the same.
• Compatible with SeaStar Power Purge system.
• Compatible with autopilots.
• Wiring harness included.
• Ignition protected (SAE J-1171).
• Auto recognize system voltage (12V or 24V).
• ABYC, CE, NMMA, ISO 10592 Approved.
• Capable of floor or wall mount. No need to purchase extra kits.
……………………………………………………………………………………………………………………………………………..
Selection Guide
Cylinder Installation
Capilano Helm Pumps
Tubing, Hoses and Fitting Kits
Technical Information
……………………………………………………………………………………………………………………………………………..
SELECTION GUIDE
MAXIMUM OUTPUT TORQUE | APPROX. VESSEL SIZE (HULL LENGTH UP TO) | HELM PUMP MODEL | STEERING WHEEL TURNS | CYLINDER MODEL REQUIRED | ||||||
LB.IN. | (Kg M) | Planing | Displacement | Min. | Max. | Fixed | ||||
6,548 | (75) | 35′ | (11m) | 30′ | (9m) | 1250v | 3.0 | 6 | n/a | BA 150-7TM |
6,548 | (75) | 35′ | (11m) | 30′ | (9m) | 1250v | 3.0 | 6 | n/a | BA 150-7TM |
6,548 | (75) | 35′ | (11m) | 30′ | (9m) | 1250v | 3.0 | 6 | n/a | BA 150-7TM |
6,548 | (75) | 35′ | (11m) | 30′ | (9m) | 1250v | 3.0 | 6 | n/a | BA 150-7TM |
6,548 | (75) | 35′ | (11m) | 30′ | (9m) | 1250v | 3.0 | 6 | n/a | BA 150-7TM |
6,548 | (75) | 35′ | (11m) | 30′ | (9m) | 1250v | 3.0 | 6 | n/a | BA 150-7TM |
6,548 | (75) | 35′ | (11m) | 30′ | (9m) | 1250v | 3.0 | 6 | n/a | BA 150-7TM |
6,548 | (75) | 35′ | (11m) | 30′ | (9m) | 1250v | 3.0 | 6 | n/a | BA 150-7TM |
6,548 | (75) | 35′ | (11m) | 30′ | (9m) | 1250v | 3.0 | 6 | n/a | BA 150-7TM |
6,548 | (75) | 35′ | (11m) | 30′ | (9m) | 1250v | 3.0 | 6 | n/a | BA 150-7TM |
a) Consult Manufacturer for hull lengths.
back to top……………………………………………………………………………………………………………………………
CYLINDER INSTALLATION
Proper cylinder installation is the key to the successful operation of the hydraulic steering system. An incorrectly installed cylinder is subject to rapid seal and bearing wear and non-repairable damage.
An imaginary line drawn through the tiller arm hole at both hard over positions will create the cylinder centre line. With tiller arm at hard over positions, angle X and Y should be the same. Select the diagram and dimensional data that corresponds with your cylinder model.
Notice
Not all possible cylinder mounting configurations are shown, however, all necessary dimensions are shown regardless of mounting configurations.
back to top……………………………………………………………………………………………………………………………
CAPILANO HELM PUMPS
1250V, 1275V & 1350
A unique variable displacement feature on the 1250V and 1275V helms allows the helms-person to adjust the amount of steering wheel turns to their preference within a predetermined range. The 1350 helm is a fixed displacement pump.
1250V & 1275V Helm Pumps
1350 Helm Pump
back to top……………………………………………………………………………………………………………………………
TUBING, HOSES and FITTING KITS
The use of seamless soft annealed refrigeration copper tubing, type L is recommended. If flexible hose is required, use hose that has a minimum operating pressure of 1000PSI, a burst pressure of 5000PSI and the lowest available expansion factor. The 1250V requires the use of 1/2″ OD copper tube while the 1275V requires the use of 5/8″ OD copper tube. The 1350 Helm Pump requires the use of 3/4″ OD copper tube.
Cylinder Hoses
Steering systems installed with copper tubing require short pieces of flexible hose to accommodate slight cylinder movement. Hoses are supplied with 1/2″ swivel flare nuts on each end. Hoses are sold as a pair for single cylinder applications and separately for the variables of twin cylinder installations.
PART NO. | DESCRIPTION |
The following hoses are for single cylinder applications. | |
HA5731 | Cylinder Hose Kit, inc. two hoses 18″ (0.45m) long. |
The following hoses are for twin cylinder applications, select four hoses as required. | |
Single Engine | Single Engine |
Single Engine | Single Engine |
Single Engine | Single Engine |
Single Engine | Single Engine |
Single Engine | Single Engine |
Single Engine | Single Engine |
Single Engine | Single Engine |
Fitting Kits
Single steering station and additional steering station S.A.E. flare tube fitting kits are available for use with 1/2″ O.D. and 5/8″ O.D. copper tubing.
PART NO. | DESCRIPTION |
HF5590 | Fitting Kit, single station, 1/2″ copper tube. |
HF5590 | Fitting Kit, single station, 1/2″ copper tube. |
HF5590 | Fitting Kit, single station, 1/2″ copper tube. |
HF5590 | Fitting Kit, single station, 1/2″ copper tube. |
Fill and Vent Plug Kit
This kit will facilitate filling and purging of the steering system at a more convenient and accessible area than the helm pump. A through dash fitting, complete with a waterproof vent plug, 18″ (0.45m) long vinyl tube and elbow fittings are supplied with this kit
PART NO. | DESCRIPTION |
HA5450 | Fill and Vent Plug Kit |
back to top……………………………………………………………………………………………………………………………
TECHNICAL INFORMATION
HELM PUMP | 1250v | 1275v | 1350v |
displacement | 1.7cu.in. – 3.4 cu.in. | 2.7cu.in. – 5.4 cu.in. | 8 cu.in. |
1.7cu.in. – 3.4 cu.in. | 2.7cu.in. – 5.4 cu.in. | 8 cu.in. | |
Relief Valve | 1.7cu.in. – 3.4 cu.in. | 2.7cu.in. – 5.4 cu.in. | 8 cu.in. |
Ports | 1.7cu.in. – 3.4 cu.in. | 2.7cu.in. – 5.4 cu.in. | 8 cu.in. |
HELM PUMP | 1250v | 1275v | 1350v |
Relief Valve | 1.7cu.in. – 3.4 cu.in. | 2.7cu.in. – 5.4 cu.in. | 8 cu.in. |
Ports | 1.7cu.in. – 3.4 cu.in. | 2.7cu.in. – 5.4 cu.in. | 8 cu.in. |
HELM PUMP | 1250v | 1275v |
1.7cu.in. – 3.4 cu.in. | 2.7cu.in. – 5.4 cu.in. |
CYLINDER MODEL SPECIFICATION | |||
CYLINDER MODEL | STROKE | VOLUME | TORQUE @ 1000psi 70 bar @ 35 Degrees |
BA 150-7 models | 7″–178 mm | 10.2 cu.in. (167cc) | 7117 in/lbs (81 Kg) |
BA 150-7 models | 7″–178 mm | 10.2 cu.in. (167cc) | 7117 in/lbs (81 Kg) |
BA 150-7 models | 7″–178 mm | 10.2 cu.in. (167cc) | 7117 in/lbs (81 Kg) |
BA 150-7 models | 7″–178 mm | 10.2 cu.in. (167cc) | 7117 in/lbs (81 Kg) |
BA 150-7 models | 7″–178 mm | 10.2 cu.in. (167cc) | 7117 in/lbs (81 Kg) |
BA 150-7 models | 7″–178 mm | 10.2 cu.in. (167cc) | 7117 in/lbs (81 Kg) |
BA 150-7 models | 7″–178 mm | 10.2 cu.in. (167cc) | 7117 in/lbs (81 Kg) |
BA |
back to top……………………………………………………………………………………………………………………………